• <track id="jmglt"><i id="jmglt"><del id="jmglt"></del></i></track>

      1. <span id="jmglt"><blockquote id="jmglt"><nav id="jmglt"></nav></blockquote></span>

        <ol id="jmglt"><blockquote id="jmglt"></blockquote></ol><track id="jmglt"><em id="jmglt"></em></track>

          1. 你的位置:首頁 > 公司產品 > 常見問題

            Strange field water heater won't catch fire?

            更新:2016/5/10 16:28:10      點擊:
            • 產品品牌   
            • 產品型號   
            • 產品描述

              ...

            產品介紹
            Strange field water heater won't catch fire?
            A, question for power supply
            Water heater can't fire solution: check the ac power plug lights are bright, to rule out power supply part of the question.
            Second, the electromagnetic valve failure
            Water heater can't fire the solution: if only heard burning burning, no \"click\" magnetic absorption electromagnetic valve, may be electromagnetic valve damage or aging, aging of the solenoid valve, will not be controlled, can suck at the beginning of the lighter one, played on fire, but immediately closed stalled again; May also for the gas pressure is too high or too low, using cylinder gas water heater will appear the cylinder pressure reducing valve output pressure too high or too low to use water heater can't play on fire; Is more likely for the solenoid valve with dirt. Electromagnetic valve cannot pass gas, gas, natural gas, liquefied petroleum gas, artificial coal gas) will not be able to come out, can't come out, so that doesn't work. Before confirm the solenoid valve is good or bad to confirm incinerator control circuit is normal, if there is failure, unable to control the electromagnetic valve and off.
            Three, the electric fault incinerator
            Water heater can't fire solution: pulse burning and controller one party has fault, water heater is not burning.
            Four: burning or induction porcelain porcelain needle
            Water heater can't fire the solution: a. pin offset or aging burned very difficult, can replace or would fire needle was right; B. induced aging, can be induced to polish stow (regardless of the flames of the fire or a small fire can be fully burning sensing needle).
            Five, the water pressure
            Water heater can't fire solution: a. water down when the water heater can't normal boot;
            B. filter clogging caused water to flow through water, clean can.
            Six, moisture linkage of failure
            Water heater can't fire solution: a. moisture linkage cannot push valve inside tympanic membrane aging or damage to the micro switch;
            B. micro switch bad.
            Seven, air switch is not open or inlet filter clogging
            Water heater can't fire solution: open air supply, air intake filter.
            Eight, gas
            Water heater can't fire the solution: such as liquefied petroleum gas water heater from natural gas quality, p after this kind of situation need to be liquefied gas to natural gas water heater can use access.
            After nine, valve seal gas corrosion was risen.
            Water heater can't fire solution: replacement parts.
            Ten, normal exhaust pipe can't
            Water heater can't fire solution: a. pipe jam, finishing a pipe blockage; B. a pipe is too long, not installed correctly.

            奇田熱水器打不著火怎么辦?
            一、電源疑問
            熱水器打不著火的解決方法:檢查交流電源插頭指示燈是否亮,先排除電源供電部分的疑問.
            二、電磁閥故障
            熱水器打不著火的解決方法:若焚燒的時候只聽到焚燒聲,沒有電磁閥“嗒”磁吸聲,可能為電磁閥損壞或者老化,電磁閥老化,會不受控制,在打火開始時能吸合一下,打得著火,但隨即閉合又熄火了;也可能為燃氣壓力過高或過低,使用鋼瓶氣的熱水器會出現鋼瓶減壓閥輸出壓力過高或過低使用熱水器不能打著火;更可能為電磁閥有臟物。電磁閥不能過氣,燃氣(天燃氣、液化石油氣、人工煤氣)就不能出來,不能出來,以致點不著火。在確認電磁閥好壞之前要確認焚燒器控制電路是否正常,若有故障,不能控制電磁閥吸合。
            三、電焚燒器故障
            熱水器打不著火的解決方法:脈沖焚燒器和控制器有一方有故障,熱水器均不能焚燒。
            四:焚燒瓷針或感應瓷針疑問
            熱水器打不著火的解決方法:a.焚燒針偏位或老化時焚燒十分困難,可替換或將焚燒針正確安放;b.感應老化,可將感應擦亮安放好(使火焰不管大火還是小火能充分燒著感應針)即可。
            五、水壓疑問
            熱水器打不著火的解決方法:a.水壓低時熱水器無法正常啟動;
            b.進水處過濾網堵塞造成水無法正常流過,整理干凈就可以。
            六、水氣聯動裝置故障
            熱水器打不著火的解決方法:a.水氣聯動閥內鼓膜老化或損壞不能推動微動開關;
            b.微動開關壞。
            七、氣源開關未打開或進氣濾網堵塞
            熱水器打不著火的解決方法:開啟氣源,整理進氣過濾網。
            八、氣種不符
            熱水器打不著火的解決方法:深圳奇田熱水器維修比如將液化氣熱水器接到天然氣上等,p這種情況需要將液化氣熱水器改天然氣后才可以接入使用。
            九、氣門密封件被燃氣腐蝕后發漲。
            熱水器打不著火的解決方法:替換零部件。
            十、煙管無法正常排氣
            熱水器打不著火的解決方法:a.煙管有堵塞,整理煙管堵塞物;b.煙管過長,未正確安裝。
            更多產品
            在线精品国精品国产尤物

          2. <track id="jmglt"><i id="jmglt"><del id="jmglt"></del></i></track>

              1. <span id="jmglt"><blockquote id="jmglt"><nav id="jmglt"></nav></blockquote></span>

                <ol id="jmglt"><blockquote id="jmglt"></blockquote></ol><track id="jmglt"><em id="jmglt"></em></track>